Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. The burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches installed on a steering column
   12.8. Lock of ignition and drum of the lock
   12.9. Switch of a heater of back glass
   12.10. Heater of back glass
   12.11. Radio receiver and loudspeakers
   12.12. Antenna
   12.13. Bulbs of headlights of head light
   12.14. Headlights of head light
   12.15. Replacement of bulbs
   12.16. System of day inclusion of headlights
   12.17. Engine of screen wipers
   12.18. Instrument guard
   12.19. Sound signal
   12.20. System cruise control
   12.21. System of the central lock
   12.22. System of window regulators
   12.23. Rear-view mirrors with the electric drive
   12.24. Safety airbag
   + 12.25. Electroschemes


12.23. Rear-view mirrors with the electric drive

GENERAL INFORMATION

Arrangement of elements of the electric drive of glasses of a rear view

1. Block of safety locks of N2 (ALT safety lock, AM1 safety lock)
2. External rear-view mirror
3. Ignition lock
4. Block of safety locks of N1 (Safety lock of a lighter and radio receiver)
5. Regulator of provision of a mirror

Rear-view mirrors with the electric drive use two engines for change of provision of a mirror; one for adjustment in the vertical plane and one for adjustment in the horizontal.

The regulator of provision of mirrors has the switch which allows to switch management of the left and right mirrors. When the key in the lock of ignition is turned in situation ASS, lower glasses and check operation of the regulator in all provisions (adjustment of mirrors up – down and to the right – to the left) for the left and right rear-view mirrors.

Table of connection of a tester and conductivity of the regulator of provision of a rear-view mirror
1. Adjustment of a mirror to the left-to the right

Check

PERFORMANCE ORDER
1. Listen to a sound of the electric motors changing the provision of mirrors.
2. If you hear engines, but mirrors do not move probably the drive in a mirror is faulty. Remove and sort a mirror for detection and elimination of a source of malfunction.
3. If a safety lock as it should be, remove a ventilating lattice / panel of the regulator from the dashboard for receiving access to the back party of the regulator of provision of mirrors, without disconnecting a wire. Include ignition and check existence of tension on the regulator. Tension has to be present only on one plug.
4. If on the regulator there is no tension, check wires between the block of safety locks and the regulator for existence of a gap or short circuit (see the tab. Table of connection of a tester and conductivity of the regulator of provision of a rear-view mirror).
5. If on the regulator there is tension, disconnect it. Check it for conductivity of current at all provisions of the regulator. If the regulator does not carry out current, replace it.
6. Connect the regulator. Find the wire going from the regulator to the mass of the car. Without disconnecting the regulator, connect a cap wire between this wire and mass of the car. If after that mirrors work, restore grounding of the switch.
7. If the mirror still does not work, remove it and check mirror wires for existence of tension. Check tension at the included ignition, and the regulator has to be switched for adjustment of this mirror. Switch the regulator through all provisions. On one of the wires connecting the switch and a mirror there has to be tension when the regulator is in any of provisions (except the neutral situation off).
8. If at any of provisions of the regulator, tension on wires of a mirror is absent, check wires between a mirror and the regulator for existence of gaps or short circuit.
9. If tension is present, remove a mirror and check its work, having connected cap wires. Replace a mirror if it is faulty.