Toyota Corolla + 1. Maintenance instruction - 2. Maintenance 2.1. Specifications 2.2. Arrangement of knots and details 2.3. Check of level of liquids 2.4. Check of a condition of tires and pressure in tires + 2.5. Servicing through each 5000 km or 3 months + 2.6. Servicing through each 12000 km or 6 months + 2.7. Servicing through each 24000 km or 12 months - 2.8. Servicing through each 50000 km or 2 years 2.8.1. Replacement of the fuel filter 2.8.2. Check of a state and replacement of spark plugs 2.8.3. High-voltage wires, cover of the distributor and runner of a rotor 2.8.4. Service of the cooling system 2.8.5. Check of system of catching of vapors of gasoline 2.8.6. Check of an exhaust system 2.8.7. Replacement of oil, transmission liquid and filter 2.8.8. Replacement of oil in a manual transmission case 2.8.9. Zolotnik and hose of system of compulsory ventilation of a case + 2.9. Servicing through each 100000 km or 4 years + 3. Engines + 4. Cooling systems, heating + 5. Fuel, exhaust systems + 6. System of decrease in toxicity + 7. Transmissions + 8. Coupling and half shafts + 9. Brake system + 10. Suspension bracket and steering + 11. Body + 12. Electric equipment
|
Set of tools for replacement of spark plugs
1. A candle face key with a rubber insert for protection of a porcelain insulator 2. Dinamometrichesky key. It is intended for inhalings of candles (though its application is optional) 3. Graggers. It is intended for a wraparound and an inhaling of a candle
|
4. Adapter. It is intended for assembly of connection and for an otvorvchivaniye of candles in engines of different types. Depending on the car and the available tools adapters of various types are used (including the extender with the cardan hinge) 5. Set of calibers. It is intended for check of a gap between candle electrodes, has various executions. Be convinced that the set includes the caliber suitable for a candle of your car
|
Replacement of candles will require a candle face key with a graggers. The face head candle a candle is supplied with a rubber insert not to damage a porcelain insulator of a candle, and also for deduction of a candle at installation in a head of the block of cylinders. Also the caliber of round section for check and adjustment of a gap between candle electrodes, and a dinamometrichesky key for a candle inhaling (see rice is required. A set of tools for replacement of spark plugs).
Set of calibers. It is intended for check of a gap between candle electrodes, has various executions. Be convinced that the set includes the caliber suitable for candles of your car
When replacing candles it is necessary to get new candles, to expose a gap and to screw instead of old, replacing each candle separately
Prevention
Getting new candles, be convinced that their type corresponds to your car. The type of a candle is specified in the section "General Specifications", in the information plate from a reverse side of a cowl (VECI-to the plate on which standards of emissions in the atmosphere for your car), and also in the maintenance instruction of the car are also specified. If data of the specified sources differ, be guided by data of the information plate as the type of candles which is specified in the plate corresponds to type of the engine of your car.
PERFORMANCE ORDER |
1. Check a condition of new candles. At detection of any signs of damages of an insulator of a candle it is impossible to establish. |
|
2. Check a gap between electrodes of new candles. The caliber of round section is for this purpose used. The caliber has to move between electrodes under small effort, otherwise adjustment of a gap is required. |
|
3. The gap between electrodes has to correspond specified in subsection 2.1 or in the information plate from a reverse side of a cowl. If the gap does not meet standard, turn in an electrode by means of the lever on the case of a set of calibers, thus do not damage a porcelain insulator round the central electrode. |
4. If the lateral electrode does not coincide with central, turn in the lever on the case of a set of calibers before combination of both electrodes on the center of a candle. |
Prevention
At exposure of a gap to turn in only a lateral electrode.
|
|
Removal
PERFORMANCE ORDER |
|
1. Not to mix high-voltage wires replace each candle separately. Remove a high-voltage wire and a tip from a candle, holding a tip, but not a wire. Turn a tip half way, at the same time making the effort directed up, and get a wire. |
2. In the presence of compressed air blow places round a candle, having removed dirt (it is possible to use also the bicycle pump). |
|
3. Turn out a candle. Turn off I shine with a special face key with the extender. |
4. Whether irrespective of the candle will change, or to be wrapped old, check a condition of a candle according to the nomogram and define the general condition of the engine. |
|
Installation
PERFORMANCE ORDER |
|
1. Before a wraparound of a candle it is into place recommended to grease a carving with the fixing structure. Usually difficult happens to wrap a candle without distortions. |
|
2. To avoid a distortion dress on a candle a hose piece with an internal diameter of 3/8 inch (9,5 mm). The manipulation a flexible hose facilitates the correct installation of a candle at a wraparound. As soon as the candle starts being wrapped with a distortion the hose will start being scrolled on an insulator owing to what damage of a carving is prevented. Tighten a candle with the set moment (see subsection 2.1). |
3. Establish a tip, having turned half way and having at the same time made the effort directed down, against the stop in a candle electrode. |
4. Replace other candles, having repeated the procedure described above. |
|
|
|