Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   - 3.2. Diesel engine
      3.2.1. Specifications
      3.2.2. Replacement of a gear belt
      3.2.3. Removal of a head of cylinders
      3.2.4. Dismantling of a head of cylinders
      3.2.5. Partition of a head of cylinders
      3.2.6. Assembly of a head of the block of cylinders
      3.2.7. Installation of a head of cylinders
      3.2.8. Check and adjustment of gaps of valves
      3.2.9. Check of a compression of cylinders
      3.2.10. Pistons and rods
      3.2.11. Measurement of cylinders
      3.2.12. Assembly of pistons and rods
      3.2.13. Installation of pistons and rods
      3.2.14. Cranked shaft and flywheel
      + 3.2.15. Cooling system
      + 3.2.16. Lubrication system
      3.2.17. Device of injection of diesel fuel
      3.2.18. Operation of the car on diesel fuel
      3.2.19. Fuel filter
      3.2.20. Fuel pump of a high pressure
      3.2.21. Nozzles
      3.2.22. Glow plugs
      3.2.23. Adjustment of the mode of idling
      3.2.24. Adjustment of the maximum turns
      + 3.2.25. Useful tips to owners of the diesel engine
   + 3.3. Electric equipment of the engine
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment


3.2.3. Removal of a head of cylinders

GENERAL INFORMATION

Assembly drawing of a head of cylinders

1. Cover of a head of cylinders
2. Laying of a cover
3. Cover of the bearing of a rasproyedelitelny shaft
4. Compensation washer
5. Valve pusher
6. Valve crackers
7. Valve spring cup
8. Valve spring
9. Maslootrazhatelny cap of a core of the valve
10. Valve spring emphasis
11. Directing the valve
12. Camshaft
13. Bolt of a head of cylinders
14. Head of cylinders
15. The condensing vstaka
16. Union of connection of a head of cylinders
17. Laying of a head of cylinders
18. Final collector
19. Laying of a collector
20. Camshaft epiploon flange
21. Camshaft cogwheel
22. Top cover of a gear belt
23. Naprvlyayushchy roller of a gear belt
24. Returnable spring
25. Compensation washer
26. Valve saddle
27. Valve
28. Returnable toprlivny tube
29. Nozzle
30. Nozzle nest
31. Epiploon
32. Average cover of a gear belt
33. Rubber tip
34. Current tire
35. Glow plug
36. Laying of a collector
37. Inlet collector

Order of an inhaling of bolts of a head of cylinders

The description of removal and installation of a head of cylinders without removal of the engine is given below.

PERFORMANCE ORDER
1. Switch-off the accumulator.
2. Merge cooling liquid.
3. Remove tubes of nozzles, nozzles and a tube of supply of fuel.
4. Disconnect a food wire from an inlet collector. Remove from candles of 4 rubber tips, turn off 4 nuts, remove the current tire and turn out four glow plugs. Fastening of candles is shown in the right part rice. Assembly drawing of a head of cylinders.
5. Take off a gear belt as it was described in the previous chapter. Remove also a camshaft cogwheel.
6. Disconnect the gas cable mechanism.
7. Pick up the phone plum of cooling liquid and a heater tube. Thus the bracket for an engine raising is also released. Under a flange of a tube there is a laying. Disconnect a hose since one end.
8. Turn off from the forward party of the engine an average cover (32) gear belts on rice. Assembly drawing of a head of cylinders.
9. Remove six nuts and sealing washers of a cover of a head of cylinders and uncover with laying.
10. Remove a forward lifting bracket of the engine.
11. Evenly cross-wise in the sequence specified rice. An order of an inhaling of bolts of a head of cylinders, turn off eighteen bolts of a head of cylinders.

12. Lift a head of cylinders from pins in a head of cylinders and put it on a workbench. Strong sat down head of cylinders can be separated from the block of cylinders by means of the screw-driver inserted between a head of cylinders and a ledge of the block of cylinders. Do not damage thus a head of cylinders. Remove traces of old consolidation. Do not allow hit of the remains of old laying in the block of cylinders.