Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
- 6. System of decrease in toxicity
   6.1. Specifications
   6.2. Electronic control system
   6.3. Electronic control unit
   + 6.4. System of onboard diagnostics
   + 6.5. Sensors of system of automatic control of the engine
   6.6. System of catching of vapors of gasoline
   6.7. System of recirculation (EGR system)
   6.8. System of compulsory ventilation of a case (PCV system)
   6.9. Catalytic converter
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment



6.6. System of catching of vapors of gasoline

GENERAL INFORMATION

System of catching of vapors of gasoline

A. Stopper of a jellied mouth
B. Control valve
S. Termopnevmoklapan
D. A tank with an absorber
E. Channel P

Operating mode of valves

Temperature
In a tank the increased depression
In a tank elevated pressure
It is above 54 °C
It is below 35 °C
State termopnevmo-
valve
It is open
It is closed
Provision of a butterfly valve
The gate connects the channel P to the inlet highway
The gate closes the channel P
Control valves of a tank
1
It is closed
It is open
2
It is open
It is closed
3
It is open
It is closed
Control valve of a jellied mouth
Mode of removal of vapors of gasoline
Purge of a fuel tank
Couples from a tank are absorbed in a tank
Couples from a tank with an absorber go to the inlet highway
Couples from a tank are absorbed in a tank

This system is intended for catching of vapors of gasoline in a fuel tank, in a chamber of a butterfly valve and the soaking-up collector, thereby preventing their hit in the atmosphere in the form of hydrocarbons.

The system consists of a tank with an absorber (absorbent carbon), the pipelines connecting an absorber to a fuel tank, a thermopneumatic valve and the control valve.

On the idle engine of couple of gasoline get to an absorber from a tank and a chamber of a butterfly valve where there is their absorption. At start of the engine the tank with an absorber is blown by a stream of the air which is soaked up by the engine, couples are fond of this stream and are burned up in the combustion chamber.

The tank is equipped with three ball valves assembled in the uniform case. Depending on power setting and pressure in a fuel tank ball valves connect or separate a tank with a thermopneumatic valve (which it is included consistently with a chamber of a butterfly valve).

Check

PERFORMANCE ORDER
1. Such malfunctions in system as failure of the control valve, damage of a tank with an absorber, stratification or cracking of hoses, the wrong accession of hoses, lead to unstable work idling and to deterioration of traction qualities of the engine. Check a condition of laying of a stopper of a jellied mouth of a tank (see subsection 5.7).
2. Obvious loss of gasoline or a smell of gasoline in salon can be caused by leakage of fuel pipes, cracks or other damages of a tank with an absorber, failure of the control valve, and also a detachment, the wrong accession, perezhatiy, a mastication or mechanical damage of connecting hoses.
3. Check a condition of each hose connected to a tank, surveying a hose on all length. If necessary replace a hose.
4. Whether check there are dribbles of gasoline in the lower part of a tank. If there is a leak, replace a tank and check a condition of hoses and correctness of their connection.
5. Examine a tank. At detection of cracks or mechanical damages replace a tank.
6. Check purity of the filter and serviceability of the control valve. Give to a tube for a tank purge air under small pressure. Air has to pass freely from other tubes. Otherwise replace a tank.
7. Check work of a thermopneumatic valve. On completely cooled down engine give the manual pump air to the channel A. The thermopneumatic valve should not pass air. Warm up the engine up to the temperature not below 55 °C. Now the valve has to pass air. Otherwise replace a thermopneumatic valve.

Replacement of a tank with absorbent carbon

PERFORMANCE ORDER
1. Disconnect hoses from a tank, previously having marked them.
2. Turn off fastening bolts, give a tank together with an arm down, disconnect hoses from the control valve and remove a tank from the car.
3. Installation is carried out upside-down.








thai rent a car hua hin . http://www.get-video.online/ convert free and online youtube video links to mp3.