Toyota Corolla + 1. Maintenance instruction + 2. Maintenance - 3. Engines - 3.1. Petrol engines - 3.1.1. Repair work without dismantle of the engine from the car 3.1.1.1. Specifications 3.1.1.2. Installation of the piston of the 1st cylinder in MW of a step of compression 3.1.1.3. Cover of a head of the block of cylinders 3.1.1.4. The soaking-up collector 3.1.1.5. Final collector 3.1.1.6. Gear belt 3.1.1.7. Forward epiploon of the crankshaft 3.1.1.8. Cam-shaft epiploon 3.1.1.9. Cam-shafts and pushers (engines of 1,3 l) 3.1.1.10. Cam-shafts and pushers (l engines 1,6 and 1,8) 3.1.1.11. Head of the block of cylinders 3.1.1.12. Oil pallet 3.1.1.13. Oil pump 3.1.1.14. Flywheel (or leading disk of the hydrotransformer) 3.1.1.15. Back epiploon of the crankshaft 3.1.1.16. Engine mount details + 3.1.2. Dismantle and capital repairs + 3.2. Diesel engine + 3.3. Electric equipment of the engine + 4. Cooling systems, heating + 5. Fuel, exhaust systems + 6. System of decrease in toxicity + 7. Transmissions + 8. Coupling and half shafts + 9. Brake system + 10. Suspension bracket and steering + 11. Body + 12. Electric equipment
|
Removal
PERFORMANCE ORDER |
1. Disconnect the battery from weight. |
Prevention
If the stereoradio tape recorder of the car is equipped with security system, before a battery detachment from weight be convinced that you know an activation code.
|
2. Disconnect hoses of system of compulsory ventilation of a case from a cover of a head of cylinders. |
3. Disconnect high-voltage wires from spark plugs, undertaking the isolating tips, but not wires. |
|
4. On engines 1,6 and 1,8 of l turn off two bolts of a cover of a head of the block of cylinders from a gear belt, get a cover of plaits of conducting and conducting. |
|
5. Turn off nuts of fastening of a cover (are specified by shooters), uncover heads of cylinders and laying. (On engines of 1,3 l in forward part there is an additional nut.) If the cover does not give in, in blows of a hammer through wooden laying loosen a cover. If this reception does not help, between a head of cylinders and a cover enter the flexible pallet and open consolidation. |
Prevention
It is not allowed to separate with a force a cover from a head of cylinders, hooking the tool as it is possible to damage surfaces of a prileganiye of these details that will lead to an oil leak after assembly.
|
|
Installation
PERFORMANCE ORDER |
|
1. Before installation carefully clear contact surfaces of a head of cylinders and a cover. In the absence of hardenings or cracks, and also at small run rubber laying can be not changed. Before installation of a cover of a head of cylinders be convinced available sealants of plugs of spark plugs from the inside of a cover. |
2. Remove laying and wash out the condensed surfaces solvent of varnishes or acetone. Establish new laying, having evenly pressed it on a cover contour into a flute. Existence on the condensed surfaces of oil pollution at assembly can be the reason of a leak of oil from under laying. |
3. Apply RTV sealant on the condensed places near a rubber cap, the distributor of ignition and a cover of an epiploon of a cam-shaft. |
4. Establish a cover, wrap nuts. |
5. Evenly tighten nuts in three-four receptions with the set moment. |
6. Establish other details, start the engine and check existence of a leak of oil. |
|
|
|