Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
- 9. Brake system
   9.1. Specifications
   9.2. System of anti-blocking of brakes (ABS)
   9.3. Brake shoes of forward brakes
   9.4. Support of forward brakes
   9.5. Brake shoes of back disk brakes
   9.6. Support of back disk brakes
   9.7. Brake disk
   9.8. Brake shoes of back drum brakes
   9.9. Working cylinder
   9.10. Main cylinder of brake system
   9.11. Brake hoses and tubes
   9.12. Hydraulic system of brakes
   9.13. Vacuum amplifier
   9.14. Emergency brake
   9.15. Ropes of the emergency brake
   9.16. Brake pedal
   9.17. Switch of headlights of a stoplight
   9.18. Valve of restriction of pressure sensitive to car loading
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment


9.5. Brake shoes of back disk brakes

GENERAL INFORMATION

Prevention

Brake shoes need to be replaced at once on two wheels – never replace brake shoes only on one wheel.

The dust formed as a result of wear of brake shoes contains the asbestos hazardous to health. Do not blow off it by means of compressed air and do not inhale.

It is forbidden to use solvents on the basis of gasoline for cleaning of the mechanism of brakes. Use only a special cleaner for the mechanism of brakes.


PERFORMANCE ORDER
1. Remove a cap from a tank of brake fluid.
2. Turn off nuts of fastening of wheels, lift back part of the car and establish it on support. Block forward wheels.
3. Remove a wheel and release the emergency brake. It is necessary to replace at once all four brake shoes of back brakes. Not to mix them, work on each of wheels in turn.
4. Get the top and lower bolts and remove a support from brake shoes and the holder of blocks (see rice. Elements of a support of back disk brakes).
5. Suspend a support on a suspension bracket spring by means of a piece of a wire; do not allow a support to hang on a brake hose and a rope of the emergency brake.
6. Remove external antinoise laying and an external brake shoe, and then internal antinoise laying and an internal brake shoe.
7. Remove two fixing plates of brake shoes; examine them on existence of damages and replace if it is necessary (good plates at installation on the holder of blocks have to be latched; if they weakened or are deformed – replace them).
8. Carefully examine a brake disk, being guided by the instructions provided in subsection 9.7. If its surface needs processing, remove a disk, being guided by the instructions provided in the same section. At removal of a disk, it is possible to remove brake shoes also.
9. Establish fixing plates of brake shoes, new brake shoes and laying. Check that the ends of blocks were correctly established on fixing plates and establish an internal brake shoe so that the indicator of wear was from above.
10. Before installation of a support on new (thicker) brake shoes, it is necessary to take away the self-regulating mechanism back. For this purpose turn the support piston clockwise by means of flat-nose pliers which sponges are established in lock flutes (1) on a piston surface. Continue to turn the piston until it begins to rotate freely, then combine lock flutes with a ledge (2) on a support.
11. Establish a support on brake shoes, having inserted a ledge on the back party of an internal brake shoe into a lock flute on the support piston.
12. Establish the top and lower bolts and tighten them till the demanded inhaling moment (see the tab. Moments of an inhaling of threaded connections).
13. Establish a wheel, then lower the car on the earth. Tighten nuts of fastening of a wheel till the demanded inhaling moment (see the tab. Moments of an inhaling of threaded connections).

14. After completion of work, squeeze out a brake pedal several times for automatic adjustment of back brakes. Check the level of brake fluid, having added it if it is necessary. Check work of brakes before normal operation of the car.