Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines
      + 3.1.1. Repair work without dismantle of the engine from the car
      - 3.1.2. Dismantle and capital repairs
         3.1.2.1. Specifications
         3.1.2.2. Diagnostics of the engine by means of a vakuumer
         3.1.2.3. Check of a compression in engine cylinders
         + 3.1.2.4. Dismantle of the power unit - methods and safety measures
         3.1.2.5. Alternatives of capital repairs of the engine
         3.1.2.6. Order of dismantling of the engine
         3.1.2.7. Head of the block of cylinders
         3.1.2.8. Repair of valves
         3.1.2.9. Shatunno-porshnevaya group
         3.1.2.10. Dismantle of the crankshaft
         3.1.2.11. Block of cylinders
         3.1.2.12. Honningovaniye of cylinders
         3.1.2.13. Cranked shaft
         3.1.2.14. Radical and shatunny bearings
         3.1.2.15. Engine assembly order
         3.1.2.16. Piston rings
         3.1.2.17. Installation of a cranked shaft and check of gaps of radical bearings
         3.1.2.18. Back epiploon
         3.1.2.19. Installation of shatunno-piston group
         3.1.2.20. Start-up of the engine after repair and a running in
   + 3.2. Diesel engine
   + 3.3. Electric equipment of the engine
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.1.2.12. Honningovaniye of cylinders

GENERAL INFORMATION

The adaptation for a honningovaniye of the brush type

Persons who never carried out a honningovaniye, are recommended to perform works by means of the "brush" adaptation.

Before assembly of the engine it is necessary to otkhonningovat cylinders to provide tightness of combustion chambers with a dense prileganiye of piston rings to walls of cylinders.

Adaptations of two types – flexible "brush" and the adaptation with the sprung heads from a grinding stone are usually used to a honningovaniye of cylinders (the last gained the widest circulation). Both adaptations yield good results, however flexible "brush" will be suitable for the unexperienced motorist better, to work with which much easier. The honningovaniye also requires kerosene, or oil for a honningovaniye, rags and the electric drill. The electric drill has to work at small turns, at a constant speed of rotation. The big drill on a drill of 12-13 mm, or a drill with a variable speed of rotation at 3/8 inch (9–10 mm) will approach.

Prevention

In the absence of the adaptation for a honningovaniye this operation can be executed for a small payment in workshops.

PERFORMANCE ORDER

1. Before a honningovaniye establish covers of radical bearings of a cranked shaft (without inserts) and tighten bolts with the set moment.
2. Clamp the adaptation in the electric drill, fix grinding heads and enter the adaptation into the first cylinder.
	3. Well oil a cylinder surface, turn on the electric drill and periodically move it up and down in the cylinder. Thus on a surface of walls of the cylinder the structure of the thin lines (1) which are crossed at an angle about 60 ° has to be formed. All the time plentifully grease a cylinder surface. Do not remove excessive amount of material, finish a honningovaniye after operational development of a surface.
Prevention Some manufacturers of piston rings recommend a little smaller corner of crossing of structure of thin lines, than 60 °. Study the instruction attached to piston rings.
4. During rotation do not get the adaptation. After switching off of a drill continue to move it up and down to a full stop, then squeeze adaptation legs with grinding heads and get from the cylinder. If the cylinder honningutsya by the brush, switch off a drill, then rotating the brush in the direction of normal rotation, get it from the cylinder.
5. Wipe the cylinder from oil and repeat operation on other cylinders.
6. After end of a honningovaniye a small file chamfer the upper edge of each cylinder to prevent jamming of rings at installation of pistons in cylinders. Be careful, do not scratch a file of a wall of cylinders.
7. All block of cylinders should be washed out again warm water with detergent to remove the remains of abrasive material from a honningovaniye.
Prevention Cylinders are considered pure if on the protirochny fabric which is not leaving pile, moistened with oil for the engine there are no traces of grayish color. Surely clean oil channels and openings a brush, wash out them flowing water.
8. After washing dry up the block of cylinders and oil veretenny all processed surfaces that will protect them from corrosion. Prior to assembly of the engine store the block of cylinders under a plastic cover.