Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines
      + 3.1.1. Repair work without dismantle of the engine from the car
      - 3.1.2. Dismantle and capital repairs
         3.1.2.1. Specifications
         3.1.2.2. Diagnostics of the engine by means of a vakuumer
         3.1.2.3. Check of a compression in engine cylinders
         + 3.1.2.4. Dismantle of the power unit - methods and safety measures
         3.1.2.5. Alternatives of capital repairs of the engine
         3.1.2.6. Order of dismantling of the engine
         3.1.2.7. Head of the block of cylinders
         3.1.2.8. Repair of valves
         3.1.2.9. Shatunno-porshnevaya group
         3.1.2.10. Dismantle of the crankshaft
         3.1.2.11. Block of cylinders
         3.1.2.12. Honningovaniye of cylinders
         3.1.2.13. Cranked shaft
         3.1.2.14. Radical and shatunny bearings
         3.1.2.15. Engine assembly order
         3.1.2.16. Piston rings
         3.1.2.17. Installation of a cranked shaft and check of gaps of radical bearings
         3.1.2.18. Back epiploon
         3.1.2.19. Installation of shatunno-piston group
         3.1.2.20. Start-up of the engine after repair and a running in
   + 3.2. Diesel engine
   + 3.3. Electric equipment of the engine
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.1.2.13. Cranked shaft

Check of technical condition

PERFORMANCE ORDER

1. Wash out a cranked shaft solvent and dry a stream of compressed air (in the presence).
2. Check uniformity of wear of radical and shatunny necks, existence on them of zadir, cracks or a local erosion.
3. Remove from oil openings all agnails by means of a grinding stone, a rigid brush or a file.
4. Clean oil channels a rigid brush and wash out a strong stream of solvent.
5. Check for existence on other parts of the crankshaft of cracks and mechanical damages. For identification of the latent defects the crankshaft is recommended to be handed over in a workshop of car service.
	6. Measure by a micrometer diameter of radical and shatunny necks, compare result to standard value. Check ovality of radical and shatunny necks of a shaft, having measured their diameter in several points on a circle. Check conicity of necks for what measure diameter of a neck in places about shaft counterbalances, and compare results.
7. It is also necessary to check a crankshaft beating though prisms of the big size will be necessary for this measurement. In the absence of the necessary equipment, the beating can be checked in auto repair shops.
8. In the presence of damages on shaft necks and also if ovality, conicity and wear of necks exceed the set limits, the shaft should be handed over on repolishing in a specialized workshop. After repair of a shaft, it is necessary to replace radical and shatunny bearings repair.
9. Check existence of signs of wear and damages on necks under forward and back epiploons. If on a neck the deep flute of development from a working edge of an epiploon was formed, there are scratches or other damages, the new epiploon will not condense a neck. In certain cases the shaft can be repaired by a napressovka of the thin plug on the condensed neck for what it is necessary to address in a workshop. If repair is impracticable, the crankshaft should be replaced new or restored.