Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross stability (forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and bearing of a nave (forward wheel)
   10.9. Stabilizer of cross stability (back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross drafts of a suspension bracket
   10.13. Nave and bearing (back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment


10.12. Cross drafts of a suspension bracket

GENERAL INFORMATION

Drafts and cross-piece of a back suspension bracket

1. Suspension bracket cross-piece
2. Cross draft of a suspension bracket of N2
3. Cross draft of a suspension bracket of N1
4. Longitudinal draft

Removal

PERFORMANCE ORDER
1. Turn off nuts of fastening of a back wheel, lift back part of the car and establish it on support.
2. Block forward wheels and remove a back wheel.
Cross draft of N2
3. If on the car the valve of restriction of pressure in a contour of back brakes is installed, sensitive to car loading – turn off a lock-nut, the fixing lower spring of the valve to the right cross draft of N2. Try not to twist the adjusting nut established is slightly higher. It is recommended to mark an adjusting nut and a carving of fastening of a spring with quick-drying paint in order that then they could be established in initial situation.

4. Remove the nut and a washer since the external end of cross draft fixing it to an arm of a nave and remove a bolt (if you remove only draft of N2, the bolt does not need to be got).

5. Turn off and remove the nut and a washer since the internal end of cross draft fixing it to a suspension bracket cross-piece.

6. Remove cross draft of N2.
Prevention

Do not turn off a lock-nut and do not rotate an adjusting coupler; if you turn off a coupler, it will change a convergence of back wheels.


Cross draft of N1
7. Turn off the nut and a bolt fixing the internal end of draft.
Also, turn off the nut and a bolt fixing the external end of thirst for a nave arm. Remove the central section of an exhaust pipe and isolation of an exhaust pipe (see subsection 5.13). If on the car the valve of restriction of pressure in a contour of back brakes, sensitive to car loading is installed, disconnect fastening of the lower spring (see point 3).
8. Establish a jack under a cross-piece of a back suspension bracket. Turn off four bolts fixing a cross-piece (see rice. Drafts and cross-piece of a back suspension bracket). Lower a cross-piece so that it was possible to get the long through bolt fixing cross drafts.
9. Turn off and remove a bolt and a nut of fastening of forward cross thirst for an arm of a nave of a back wheel.
10. Remove the nut and a bolt fixing forward cross thirst for a suspension bracket cross-piece.

11. Remove cross draft of N1.