Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross stability (forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and bearing of a nave (forward wheel)
   10.9. Stabilizer of cross stability (back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross drafts of a suspension bracket
   10.13. Nave and bearing (back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment


10.16. Steering wheel

GENERAL INFORMATION

Prevention

On these models the safety airbag is installed. The airbag of safety can reveal (it will be filled with air) at any time when it is connected to the accumulator. In order that it incidentally did not reveal (and did not put a trauma), turn a key in the ignition lock in the situation LOCK and disconnect a wire of the negative plug of the accumulator before work with a safety cushion. After a detachment of the accumulator wait at least two minutes before work, (the module of a safety cushion has the condenser block which has to be discharged completely). For more information watch chapter describing electric equipment of the car.


Removal

PERFORMANCE ORDER
1. Turn a key in the ignition lock in the situation OFF, then disconnect a wire of the negative plug of the accumulator. If on the car the safety airbag is installed, wait at least two minutes before further work.
Prevention

Put the safety airbag face up.


2. For receiving access to fixing screws of the airbag of safety remove casing halves of a steering column on each side.
3. Turn a steering wheel so that forward wheels looked precisely directly, then remove small casings (if are established) a steering wheel on each side and turn off the T30 screws with face heads fixing the safety airbag to a steering wheel.
4. Turn off screws so that the rim on a circle of the screw rested against a nest (1 – the face screw, 2 – a screw nest). Remember that on some models, two screws, and on the right side only one are on the left side located.
5. Remove the safety airbag from a steering wheel.
6. Raise a fixing uvula of the socket of connection of a pillow and disconnect it.

Prevention

Put the safety airbag face up.


7. Disconnect the socket of connection of system cruise control (if it is established).
8. Turn off a fixing nut of a steering wheel (it is specified by shooters) and note the provision of installation of a steering wheel in relation to a shaft of a steering column (if the mark is not made yet or if they do not coincide) for simplification of installation of a steering wheel.
9. By means of a stripper remove a steering wheel from a shaft of a steering column. If the steering wheel is not removed from a shaft of a steering column, use the removable device.

Installation

PERFORMANCE ORDER
1. Check that forward wheels looked precisely directly. Turn the rope twirled by a spiral counterclockwise a hand until it becomes strong to resist. Turn a rope clockwise on three turns and combine two red indexes (the rope will be scrolled approximately on three turns to the right or to the left from the center).
2. For installation of a steering wheel, combine a mark in a steering wheel with a mark on a shaft of a steering column and put on a steering wheel a shaft of a steering column. Establish a fixing nut and tighten it till the demanded inhaling moment (see subsection 10.1).
3. Connect the socket of connection of wires of system cruise control.
4. Connect the socket of connection of wires of the airbag of safety and lower a fixing uvula.
5. Check that the socket of connection of the airbag of safety was located correctly, and wires disturbed nothing (1 – connection, 2 – wires for a safety cushion). Then, install the airbag of safety and tighten fixing screws with heads under face a key till the demanded inhaling moment (see subsection 10.1).
6. Connect a wire of the negative plug of the accumulator.