Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross stability (forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and bearing of a nave (forward wheel)
   10.9. Stabilizer of cross stability (back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross drafts of a suspension bracket
   10.13. Nave and bearing (back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment


10.2. Rack of a suspension bracket (lobby)

Removal

PERFORMANCE ORDER
1. Turn off nuts of fastening of a wheel, lift the car and establish it on support. Remove a wheel.
2. Turn off bolts of fastening of an arm of a brake hose to a rack
suspension brackets. If on the car the system of ABS is installed, remove a plait of wires of the sensor of speed from a rack, having turned off a bolt of fastening of an arm.
3. Turn off two nuts of fastening (are specified by an arrow) are resistant to a rotary fist and beat out bolts by means of a hammer and a punch.
4. Remove a rack from a rotary fist. Watch to stretching the internal CV JOINT of a half shaft. Also, watch that the rotary fist did not overturn outside and did not hang on a brake hose.
5. Holding one hand a suspension bracket rack with a spring, turn off nuts of the top fastening of a rack to a body (are specified by shooters). Remove a rack with a spring from under a car wing.

Check

PERFORMANCE ORDER
1. Check a rack for existence of leak of liquid from the shock-absorber, for existence of dents, cracks or other damages which demand replacement of a rack.
2. Check a spring for existence of cracks or the broken-away slices on a spring covering, (it will lead to a premature exit of a spring out of operation because of corrosion). Examine a spring nest on existence of cuts, consolidations or other damages and wear tracks.
3. If there are any damages or wear tracks, pass to the section describing dismantling of a rack (see subsection 10.3).

Installation

PERFORMANCE ORDER
1. Establish a suspension bracket rack under the aegis of the car and insert bolts of the top fastening into openings in a body. Acquire nuts. It is best of all to perform this work together, as a rack rather heavy and big.
2. Establish a rotary fist on flanges of a rack and insert two fixing bolts. Put the clamps till the demanded inhaling moment (see subsection 10.1).
3. Establish an arm of a brake hose on a rack of a suspension bracket and reliably twirl a fixing bolt. If on the car the system of ABS is installed, establish a fixing arm of wires of the sensor of speed of rotation of a wheel.
4. Establish a wheel and acquire nuts of fastening of a wheel, then lower the car on the earth and tighten nuts till the demanded inhaling moment (see subsection 10.1).
5. Tighten nuts of the top fastening of a rack of a suspension bracket till the demanded inhaling moment (see subsection 10.1).
6. Address to auto repair shop for check and if it is necessary, implementation of adjustment of forward wheels.