Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
- 1. Maintenance instruction
   1.2. Codes of models
   1.3. Control panel
   + 1.4. Combination of devices
   + 1.5. Governing bodies and instrumentations
   - 1.6. Start-up of the engine and driving
      1.6.1. Check before start-up of the engine
      1.6.2. Check after start-up of the engine
      1.6.3. Methods of driving
      + 1.6.4. Towage of the trailer
      1.6.5. Actions at refusal of start-up of the engine
      1.6.6. Obligatory set of tools and spare wheel
      1.6.7. Replacement of a wheel
      1.6.8. Towage of the car
      1.6.9. Motor compartment
      1.6.10. Arrangement of safety locks
      1.6.11. Check of level of oil in the engine
      1.6.12. Oil brand choice
      1.6.13. Check of level of cooling liquid
      1.6.14. Composition of cooling liquid
      1.6.15. Check of pressure in tires
      1.6.16. Replacement of tires
      1.6.17. Shift of wheels
      1.6.18. Installation of winter tires and chains
      1.6.19. Precautionary measures for cast aluminum disks
      1.6.20. Check of an external condition of the battery
      1.6.21. Check of level of electrolyte
      1.6.22. Battery charging
      1.6.23. Check and replacement of safety locks
      + 1.6.24. Replacement of lamps
   1.7. Specifications
   1.8. Adjusting data, filling capacities and liquids
   + 1.9. Possible malfunctions
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment


1.6. Start-up of the engine and driving

Before start-up of the engine

PERFORMANCE ORDER
1. Examine a platform near the car.
2. Take a place, adjust the provision of a seat, a head restraint and a tilt angle of a wheel.
3. Adjust the provision of rear-view mirrors.
4. Close all doors.
5. Be fastened by a belt.

Before inclusion of a starter

PERFORMANCE ORDER
1. Put the car on the emergency brake. Switch off everything unnecessary consumers and devices of lighting.
2. On cars from mechanical KP press a coupling pedal to a floor and put KP control lever in neutral situation. Hold a pedal pressed before start of the engine.
3. On cars with automatic transmission transfer the selector lever to situation P. If it is necessary to start the decayed engine during the movement, transfer the lever to situation N. If the lever is in any situation corresponding to the movement, the safety device will prevent inclusion of a starter.
4. Only on cars with automatic transmission press a brake pedal to the full and hold prior to the movement.

 Start of the engine


Prevention

Period of operation of a starter at start should not exceed 15 pages. Otherwise the starter and cables overheat.

Do not disperse sharply on the cold engine.

Esp the engine often becomes deaf or is badly started, immediately check a condition of the engine.


MODEL 2E

PERFORMANCE ORDER
1. Follow the instructions stated above.
Start under normal conditions, engine cold
2. Press a pedal of a butterfly valve to the full and release. Thus the system of increase of turns of idling and the automatic starting arrangement join.
3. Take away a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after start of the engine.
4. Let's get warm to the engine during 10 with then the car is ready to the movement.
Start at a negative temperature or after the parking within several days
5. Before inclusion of a starter press 2–3 times a pedal of a butterfly valve to the full and release. Thus there is an enrichment of mix at start-up of the engine.
6. Take away a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after start of the engine.
7. Let's work to the engine during 30 with, quickly press a pedal of a butterfly valve and lower idling turns.
8. Let's get warm to the engine within several minutes then the car is ready to the movement.
Start-up of the warm engine
9. Press a pedal of a butterfly valve approximately on a half of the course and include a starter, having turned the ignition key in the situation START. Release a key and a pedal of a butterfly valve after start of the engine.
Start-up of the hot engine
10. Press a pedal of a butterfly valve to the full and include a starter, having turned the ignition key in the situation START. Release a key and a pedal of a butterfly valve after start of the engine. Not to press one pedal any more.
Start-up of the decayed engine
11. Repeat the actions described above depending on engine temperature.
Refusal of start-up of the engine
12. Be guided by the description in subsection 1.6.5.

MODEL 4E-FE, 4A-FE and 7A-FE (FOR the CARS SOLD IN GERMANY)

Cars are equipped with multichannel system of direct injection of fuel (or consecutive injection) which automatically prepares the mix necessary for start-up of the engine. Irrespective of a thermal state the engine is started as follows.

PERFORMANCE ORDER
1. Follow the instructions stated above.
Start under normal conditions
2. Take away a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after start of the engine.
3. To warm up the engine only at a trip, but not idling. Move with a moderate speed until temperature of cooling liquid does not increase to an operating level.
4. If the engine decayed, start it, having repeated procedure of start in normal conditions.
At refusal of start-up of the engine
5. Be guided by the description in subsection 1.6.5.

MODEL 4E-FE, 4A-FE and 7A-FE (FOR ALL CARS, EXCEPT INTENDED FOR GERMANY)

Cars are equipped with multichannel system of direct injection of fuel (or consecutive injection) which automatically prepares the mix necessary for start-up of the engine. Irrespective of a thermal state the engine is started as follows.

PERFORMANCE ORDER
1. Follow the instructions stated above.
Start under normal conditions
2. Take away a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after start of the engine.
3. Let's get warm to the engine during 10 with then the car is ready to the movement.
4. In frosty conditions let's work to the engine within several minutes then the car is ready to the movement.
5. If the engine decayed, start it, having repeated procedure of start in normal conditions.
At refusal of start-up of the engine
6. Be guided by the description in subsection 1.6.5.

MODEL 2C (ON THE CARS INTENDED FOR GERMANY)

Control lamp of prestarting heating

PERFORMANCE ORDER
1. Follow the instructions stated above.
Start under normal conditions, engine cold
2. Turn the ignition key in the situation On, be convinced that the control lamp of prestarting heating lit up. Hold the ignition key in the situation On until the control lamp does not go out.
3. Press a pedal of a butterfly valve to the full and include a starter, having turned the ignition key in the situation START. Take away a foot from a pedal of a butterfly valve and release a key after start of the engine.
4. To warm up the engine only at a trip, but not idling. Move with a moderate speed until temperature of cooling liquid does not increase to an operating level.
Start-up of the warm engine
5. Press a pedal of a butterfly valve approximately on a half of the course and include a starter, having turned the ignition key in the situation START. Release a key and a pedal of a butterfly valve after start of the engine.
6. If the engine is not started, execute actions for start-up in normal conditions.
7. If the engine decayed, start it, having repeated the procedures described above depending on a thermal condition of the engine.
At refusal of start-up of the engine
8. Be guided by the description in subsection 1.6.5.
9. Coupling guard.
10. The lower bolts of fastening of a case of coupling to the block of cylinders.

MODEL 2C (ON ALL CARS, KROM INTENDED FOR GERMANY)

Control Pampas of prestarting heating

PERFORMANCE ORDER
1. Follow the instructions stated above.
Start under normal conditions, engine cold
2. Turn the ignition key in the situation On, be convinced that the control lamp of prestarting heating lit up. Hold the ignition key in the situation On until the control lamp does not go out.
3. Press a pedal of a butterfly valve to the full and include a starter, having turned the ignition key in the situation START. Take away a foot from a pedal of a butterfly valve and release a key after start of the engine.
4. Let's get warm to the engine during 10 with then the car is ready to the movement.
5. In frosty conditions let's work to the engine within several minutes then the car is ready to the movement.
Start-up of the warm engine
6. Press a pedal of a butterfly valve approximately on a half of the course and include a starter, having turned the ignition key in the situation START. Release a key and a pedal of a butterfly valve after start of the engine.
7. If the engine is not started, execute actions for start-up in normal conditions.
8. If the engine decayed, start it, having repeated the procedures described above depending on a thermal condition of the engine.
At refusal of start-up of the engine
9. Be guided by the description in subsection 1.6.5.
10. The lower bolts of fastening of a case of coupling to the block of cylinders.

Check of the car before a trip


Before a trip it is recommended to examine the car. Having spent some minutes, you will provide a safe and pleasant trip. Here only thorough acquaintance to own car and attentiveness is required.