Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
- 1. Maintenance instruction
   1.2. Codes of models
   1.3. Control panel
   + 1.4. Combination of devices
   + 1.5. Governing bodies and instrumentations
   - 1.6. Start-up of the engine and driving
      1.6.1. Check before start-up of the engine
      1.6.2. Check after start-up of the engine
      1.6.3. Methods of driving
      + 1.6.4. Towage of the trailer
      1.6.5. Actions at refusal of start-up of the engine
      1.6.6. Obligatory set of tools and spare wheel
      1.6.7. Replacement of a wheel
      1.6.8. Towage of the car
      1.6.9. Motor compartment
      1.6.10. Arrangement of safety locks
      1.6.11. Check of level of oil in the engine
      1.6.12. Oil brand choice
      1.6.13. Check of level of cooling liquid
      1.6.14. Composition of cooling liquid
      1.6.15. Check of pressure in tires
      1.6.16. Replacement of tires
      1.6.17. Shift of wheels
      1.6.18. Installation of winter tires and chains
      1.6.19. Precautionary measures for cast aluminum disks
      1.6.20. Check of an external condition of the battery
      1.6.21. Check of level of electrolyte
      1.6.22. Battery charging
      1.6.23. Check and replacement of safety locks
      + 1.6.24. Replacement of lamps
   1.7. Specifications
   1.8. Adjusting data, filling capacities and liquids
   + 1.9. Possible malfunctions
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment



1.6.7. Replacement of a wheel

PERFORMANCE ORDER
1. To prevent the movement of the car lifted on a jack, block a wheel, diagonalno opposite to the punctured. Enclose blocks in front of a forward wheel and behind the back.
2. Hook a cap slanted part of a stripper of a cap.
On cars with the petrol engine as a stripper it is possible to use the handle of a candle key.

Prevention

It is not allowed to take off a cap manually. At the address with a cap it is necessary to observe extra care to avoid injuries.


3. Before raising of the car it is necessary to weaken an inhaling of nuts of wheels. For this purpose turn off a nut counterclockwise. For receiving the maximum effort have a key so that the handle was from the right hundred-wound. At an otvorachivaniye be taken by the handle edge, watch that the key did not slide off a nut. Nuts need to be weakened only half way, completely not to turn off.
4. To establish a jack only under the places specified illustrations. The platform of installation of a jack has to be equal and firm.
5. Be convinced that in salon there are no passengers, and lift the car so that it was possible to establish a spare wheel. Remember that for installation of a spare wheel the car should be lifted above, than at removal of the punctured.
6. For rise insert the jack handle into an earring and rotate clockwise. At the very beginning of rise be once again convinced of correctness of installation of a jack.
7. Turn off nuts and remove the punctured wheel.
8. Drive a spare wheel and will expose so that openings in a disk were opposite to hairpins.
9. Lift a wheel and dress on the top hairpin. Having shaken, dress a wheel on other hairpins.
10. Before establishing a wheel, remove corrosion traces on disk prileganiye places with a metal brush. The insufficient prileganiye of a disk can lead to an otvorachivaniye of nuts and a separation of a wheel at a driving. Therefore through each 1600 km check an inhaling of nuts of wheels.
11. Screw nuts of wheels (inside conical part), tighten by hand. Wring out a wheel and at opportunity tighten nuts.
12. Lower the car and tighten nuts. For this purpose rotate the jack handle counterclockwise. For an inhaling of nuts use only a key for wheel nuts. Tighten nuts manually, use of the foreign means and tools changing the inhaling moment (a hammer, pipes, etc., and also to hold out nuts, planting the feet against a key), is not allowed.

13. Be convinced that the key is reliably dressed on a nut. Wrap nuts gradually in the order specified illustrations. Repeating sequence of an inhaling, finally tighten nuts.
14. Establish a cap in a place and slightly kill with a foot before click.
15. After change of a wheel check pressure in the tire of the established wheel. Adjust pressure according to the norms specified in part 8.
16. If pressure is lower nominal, at a small speed reach the next workshop and pump up the tire. Do not forget to wrap a gate cap, otherwise dirt can get to a zolotnik and cause to flow. In case of loss of a cap get as soon as possible and establish.
17. Lay a jack, the damaged wheel and the tool on the places. As soon as possible tighten wheel nuts a dinamometrichesky key with the set moment, repair the damaged tire.