Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
- 1. Maintenance instruction
   1.2. Codes of models
   1.3. Control panel
   + 1.4. Combination of devices
   + 1.5. Governing bodies and instrumentations
   - 1.6. Start-up of the engine and driving
      1.6.1. Check before start-up of the engine
      1.6.2. Check after start-up of the engine
      1.6.3. Methods of driving
      + 1.6.4. Towage of the trailer
      1.6.5. Actions at refusal of start-up of the engine
      1.6.6. Obligatory set of tools and spare wheel
      1.6.7. Replacement of a wheel
      1.6.8. Towage of the car
      1.6.9. Motor compartment
      1.6.10. Arrangement of safety locks
      1.6.11. Check of level of oil in the engine
      1.6.12. Oil brand choice
      1.6.13. Check of level of cooling liquid
      1.6.14. Composition of cooling liquid
      1.6.15. Check of pressure in tires
      1.6.16. Replacement of tires
      1.6.17. Shift of wheels
      1.6.18. Installation of winter tires and chains
      1.6.19. Precautionary measures for cast aluminum disks
      1.6.20. Check of an external condition of the battery
      1.6.21. Check of level of electrolyte
      1.6.22. Battery charging
      1.6.23. Check and replacement of safety locks
      + 1.6.24. Replacement of lamps
   1.7. Specifications
   1.8. Adjusting data, filling capacities and liquids
   + 1.9. Possible malfunctions
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

1.6.23. Check and replacement of safety locks

GENERAL INFORMATION

Type A

At the left – whole

On the right – fused

Type B

At the left – whole

On the right – fused

Type C

At the left – whole

On the right – fused

Tweezers for extraction of a safety lock

If headlights or other consumers do not join, check a condition of safety locks. Replace the fused safety lock.

The provision of safety locks is specified in subsection 1.8.

PERFORMANCE ORDER

1. Switch off ignition and the unemployed consumer. Get a safety lock of the refused consumer and check. The name of a chain which protects a safety lock, is specified on a cover of the assembly block (see also subsection 1.8).

2. The safety lock of type A is taken by tweezers. If you are not sure of burn-out of a safety lock, replace it obviously serviceable, having inserted into the corresponding clips. The rated current of a safety lock has to correspond specified on a cover of the assembly block.

3. In the absence of a spare safety lock it is possible to use safety locks of chains of the receiver or lighter, drive of the hatch or conditioner (the name of a chain according to CIG&RADIO, DOME, A/C) who are unreliable at the movement. The rated current of these safety locks has to correspond to current of the replaced.

4. If the rated current nevertheless does not correspond to current of the replaced safety lock, establish the safety lock calculated on smaller current, but closest suitable on value of current faulty. The safety lock with smaller current can fuse (but not at once), but it will indicate serviceability of this chain.

5. As soon as possible replace a safety lock regular. Will not prevent to get a set of spare safety locks and to carry with itself.

6. If the new safety lock fuses at once, the chain is faulty. In this case immediately address to service of Toyota car service.

7. It is forbidden to establish a safety lock with big rated current or to use self-made crossing points in order to avoid extensive damages or the fire.